Clik here to view.
error applying QOS policy to interface - hp 1920-24g
I get an error when I try to apply a QOS policy to a port as per the user guide. Switch is a HP 1920-24GI select my policy as per the user guide instructions below, I then select inbound It fails...
View ArticleVLAN and Routing problems
Guys Was wondering if somebody could help me out, im a little confused trying to work out an issue with an inherited network setup, im having a basic problem of trying to get a PC on a subnet out onto...
View ArticleRe: VLAN and Routing problems
-Does the firewall itself has entry in routing table for 192.168.12.0/24 subnet? And rules (both access an NAT ) allowing internet access for that subnet?-Don't draw wrong conclusions for switches not...
View ArticleRe: LLDP-MED and QoS DSCP Marking
Interfaces without "qos trust dscp|qos " don't trust any incoming packets, all packets will end up in the switch low prio queue.Also DSCP values aren't remarked/reset, since this requires the "qos...
View ArticleRe: error applying QOS policy to interface - hp 1920-24g
What does the policy look like?Note: No need for screen shots, you can download config file from switch
View ArticleRe: VLAN and Routing problems
Hi Thanks for your reply much appreciated, i have a static route for the subnet in the firewall, and it is listed in the routing table (attached) so as far as i can see it should know and route to the...
View ArticleRe: error applying QOS policy to interface - hp 1920-24g
#acl number 3000rule 50 permit udp destination-port eq bootpsrule 55 permit udp destination-port eq bootpcrule 60 permit ip source 10.10.30.0 0.0.0.255 destination 192.168.99.0 0.0.0.252rule 65 deny ip...
View ArticleRe: error applying QOS policy to interface - hp 1920-24g
I'd try to get rid of the "logging" statement in the ACL.Note:Are you trying to block DHCP, block traffic between the 2 subnets, and allow all other traffic?
View ArticleRe: VLAN and Routing problems
Seems like this firewall is an ASA. Try using its build in packet tracer wizard, it might give a clue where packets end up.
View ArticleRe: error applying QOS policy to interface - hp 1920-24g
Thanks for your response. I need some help with my ACLS.. Overall I would like internet only on VLAN 30 - no access to other VLANS. I want to allow DHCP requests to VLAN 1 from VLAN 30 ONLY, block all...
View Articlehp 1910 vs hp 1920 switch and packet filtering
helloi have a hp 1920-24g swtich. via the cmdline I don't seem to have the packet-filter command available on vlan interfaces. it is only available on gigabit ethernet interfaces. I want to apply an...
View ArticleRe: LLDP-MED and QoS DSCP Marking
Please let me confirm..All packtes whicht are coming from an IP Phone with DHCP EF and maybe a packet coming from a PC behind the Phone are not remarked?! The only reason for the command "qos trust...
View ArticleRe: error applying QOS policy to interface - hp 1920-24g
I was unsuccessfull with config below:The permit rules in ACL match all private ranges, on permit rules, policy applies and traffic is blocked. This works OKThe deny rules in ACL (40 50 60) are...
View ArticleRe: LLDP-MED and QoS DSCP Marking
"The only reason for the command "qos trust dscp|cos" is to put the traffic in an explicit queue? "Yes"So when I need to control the remarking I should configure a policy and apply it to the...
View ArticleRe: error applying QOS policy to interface - hp 1920-24g
as i understand it, what you write is correct when using qos for traffic filtering. the traffic behavior (in your exampl - deny) is the action that is taken, weather or not you have permit or deny in...
View ArticleRe: error applying QOS policy to interface - hp 1920-24g
afaik, policy commands are limited, you can only apply a single action, so your multiple action policy won't work.I can confirm the hp1910 has packet filter command on vlan interfaces. (and a noisy fan...
View ArticleRe: VLAN and Routing problems
I can't say that this would definitely cause any traffic issues, but you have a design issue: you have 3 Layer3 devices, with a shared subnet spanning all 3. This means you could get asymmetric...
View ArticleHP 1810-24G Daylight Saving Not Working
Hi I have a HP 1810-24G J9803A Software Version PL.2.04 The current time in Melbourne Australia is 9:17 PM and the switch is showing 08:17 PM. The switch had been rebooted. There's a forum post here...
View ArticleRe: HP 1810-24G Daylight Saving Not Working
It appears your switch doesn't have the Linux feature where you just enter your continent/city and it automatically handles DST, Australia/Canberra. There can be up to 24 * 3 timezones, not counting...
View ArticleLink Agreggation with different speed ports problem!.
Hello friends, first sorry for my English I speak spanish but i will try to do my best.I have two HP V1910 switches and i want to create a link agreggaeton between them. I can't figure how to do this...
View Article