Re: HP 1820 vlan config
Yeap each network has different IP's, as I said I dont want ANY connectivity between VLAN's I just want to chop the 24 ports into 4 x 6 port chunks this was easy to setup on my HP2510 any help...
View ArticleStacking v1910 over LACP, mixing with v1920-series?
Facing a shortage of available ports, I am considering options for expanding our current V1910-24G-PoE+ switch.One of the options is to add another V19x0 and utilise the 'stacking' feature. While I...
View ArticleRe: 1920 switches NTP
Solved - It was the firewall.On a WatchGuard via the WebUI, go to System> NTP and there is a tick box to enable as NTP server !!
View ArticleRe: v1910 ACL's Not Working
ACL this switch is actually very complicated. I have 4 vlans, 1,2,3,4. I would like to give access to VLAN 4 only to VLAN 2. What should I do?Should I set a QoS rule to any port in the case vlan...
View ArticleRe: 1920 switches MSTP
Well,finally got it working.Reset everything back to defaultsCreated MSTP region with Revision 1 this time instead of 0On each of the three edge switches, set the cost on one of the fibre ports on...
View ArticleRe: 1920 switches VOIP
Managed to get the phone configured to tag the voice vlan and untag the pc vlan.Phone now boots up and gets a DHCP address from the correct scope however I cannot get the PC to get a DHCP address.I can...
View ArticleRe: 1920 switches VOIP
Did you configure the switch port as being a trunk port, having Vlan4 tagged and Data Vlan (1?) untagged
View ArticleRe: 1920 switches MSTP
The core switch should sent out broadcasts to both fibers. On the access switch, one receiving port is in STP-block mode, this is where packets are discarded
View ArticleRe: 1920 switches MSTP
Sorry, I meant broadcasts from a client patched to one of the edge switches.
View ArticleRe: 1920 switches VOIP
I had to get a reseller to reconfigure the phone as that appears to be the only way of getting it done given that the information isnt publicly available.The display on the phone says something like...
View ArticleRe: 1920 switches MSTP
The edge switch shouldn't send out broadcast on its blocked port. However, the broadcast sent on its forwarding fiber is copied by the core switch to all it's interfaces , so it also ends up on the...
View ArticleRe: 1920 switches VOIP
All working !!!!!If anyone needs the config for an interface on an P1920 switch here it is....interface GigabitEthernet1/0/15port link-type trunkundo port trunk permit vlan 1port trunk permit vlan n nn...
View ArticleRe: V1910 Firmware doesn't work with 3Com branded switch
Unfortunately it seems that this grave upgrade issue returned with recent HP 1910-48G Switch firmware release 1910_5.20.R1516 (14-Jan-2016). I upgraded my original 3com 3CRBSG5293 (JE009A) switch to...
View ArticleHP Procurve 1920 Trunk configuration with UBNT EdgeMax Lite
Hi,Last Friday, I bought a new HP Procurve 1920 24-port layer 3 switch for my large home network with multiple subnets for replacing my old Dell PowerConnect 2716 and connected to my Edgemax Lite...
View ArticleRe: Switch port error not connected
Just traced the port to the problem device. The item in question is an XBox 360 Slim. Any idea why this device would be causing these errors? Thanks. JR
View ArticleRe: HP Procurve 1920 Trunk configuration with UBNT EdgeMax Lite
First take a look at the switch MAC address table, select addresses in VLAN300. and review originating ports.
View ArticleRe: HP Procurve 1920 Trunk configuration with UBNT EdgeMax Lite
Thanks for your reply 16again.The switch shows correct MAC adresses for VLAN300, please refer to the screenshot.As part of diagnostics, I've assigned an IP address to the switch within the same subnet...
View ArticleRe: HP Procurve 1920 Trunk configuration with UBNT EdgeMax Lite
I just took a tcp dump in the router and as far as I can see, once I try to ping the router from one of the servers, I see ARP requests but no responses are sent back.Ping from switch to router: PING...
View ArticleRe: HP Procurve 1920 Trunk configuration with UBNT EdgeMax Lite
Now it's solved after removing VLAN300 on eth2 in my UBNT EdgeMax Lite router, rebooting it and then adding back the VLAN.Magic...
View Article