Where to get newer Firmware for ProCurve 1800-24G?
Hi, I got a "new" old switch with a pretty old firmware-version (PB.02.03). Now I want to upgrad to the last firmware-version for my switch (PB.03.04).Where can I find the latest firmware?I didn´t find...
View ArticleRe: Where to get newer Firmware for ProCurve 1800-24G?
https://h10145.www1.hp.com/downloads/SoftwareReleases.aspx?ProductNumber=J9028B
View Article1910-8G Switch JG348A vlan/routing setup
I have a JG348A with software 1513P99 and I could use come assistance on getting the configuration right.I need to pass two vlans over the uplink port from a primary switch, 102 and 113. Vlan 102 is...
View ArticleBest way to connect 2 HP Procurve Switch.
Hi. I have a network with 78 end stations + 2 servers, I want to use 2 HP ProCurve 1920. What is the best way to connect both switches in the same rack and give me the best performace with cooper?...
View ArticleRe: Best way to connect 2 HP Procurve Switch.
I'm not sure I understand, but I make a Link Aggregation ...
View ArticleSFP module on HP 1910-8G
Hello,I got HP 1910-8G switch and SFP module. When I insert SFP module console gives these lines and no communication runs thru fiber: %Apr 26 14:54:59:226 2000 APPANSW00...
View ArticleRe: Best way to connect 2 HP Procurve Switch.
Well, maybe I didn't was to clear sorry. This is a new world for me. I can connect 2 switches using the ethernet port with a crosscable. But Swicthes like HP Procurve have some better ways to...
View ArticleRe: Best way to connect 2 HP Procurve Switch.
With the Trunk on ProCurve, you increase the bandwidth communication.example:You use two interfaces on each switch to the trunk, then you will have a 2GB communication channel. If happens physical...
View ArticleRe: Best way to connect 2 HP Procurve Switch.
And as theTrunkyou'll have asingle logical portforSTP...
View ArticleRe: Best way to connect 2 HP Procurve Switch.
Them u mention Link Aggregation, what is the purpose of this feature compare with the trunk feature? Thanks for your time.
View ArticleLoop Protection on 1920 jg925a
Hi I've some 1920-24g-Poe+ (jg925a) with fiber uplink.I want to enable the loop guard to prevent the network from loop.I've the MSTP configured by default (enable), in network->mstp->port setup...
View ArticleRe: 802.1X Filter-Id does not work with IPv6 ACL
It's me again. Maybe my config would help to solve the problem. This is an example where all traffic should be blocked. Of course in a real setup there would be more rules to allow traffic to the...
View ArticleHP 1920 moving ports to VLANS
Hello I just have my hands on HP 1920 we managed switch. Prior to that never had used web as managing switches, always been using CLI. I take session through switch IPI create VLANS on 1920.Move all...
View ArticleRe: HP 1920 moving ports to VLANS
Hi ! Thisswitchmodel is aL2,then hewill not dothe routingVlan.If theswitchhas anIP address inVLAN1 andyou areconnected to theVLAN2,you will notbe abletoaccesstheswitchwithout havingan L3device thatdo...
View ArticleRe: HP 1920 moving ports to VLANS
Both the switch and pc have IP address of the same subnet.i-e 10.10.10.10 for switch10.10.10.11 for pc
View Article1920 configure port security
Hello Got 1920 34G switch as a demo usint to work on and test it. previously have worked on CLI mode og HP 2520, 3COM etc. not fluent with web interface.We use port security. Below is the config...
View ArticleRe: 1910-8G Switch JG348A vlan/routing setup
What is the switchport config on the primary switch? Both VLANs tagged?
View ArticleRe: HP 1920 moving ports to VLANS
Whatvlaninswitchis associated with thatIP(VLAN interface)?Hostis on whichVLAN ??
View Article2928-SF Plus (V1910-24G) error modifying default IP
Hello there I'm having a big problem with my 3Com Baseline Switch 2928-SFP Plus. I'm confyguring the switch to my fiber optic cable network and as I do to all my new switch i need to change the default...
View Article