Re: Best method for connecting up multiple 1920 switches
If you're stick with using (forced to use) specifically the HPE OfficeConnect 1920 Switch series (PoE/non PoE models, doesn't matter)...and you want to preserve as much 1GbE ports as possible (so 48 at...
View ArticleRe: V1820-48G Web Interface goes down, stays down until reboot
I see a new PT.02.01 firmware was released last week. I've noticed that the web interface has not always came back up after a reboot, so am at a loss for how to get the new firmware uploaded.Is there...
View ArticleHP V1810-48G Ember / Fault
Hello...avery one.I have HP V1810-48G Switch with port eth 28 always blink on link indicator also fault indicator blink to.i tyred to reset my switch on factory setting but still ember with blink on...
View ArticleReduced costs with Cugic
Telephone support is and old technique for being there for your clients, yet it can be expensive – both regarding toll charges and individual hour costs.Live chat software doesn't cost more than a...
View ArticleIs anyone able to get 3Com 3CDSG8 Latest Firmware ? Where can I find it Today ?
Hi Guys:Is anyone able to get 3Com 3CDSG8 Latest Firmware ?Where can I find it ? I couldn't find it on HP site.Please help meRegards,Marcelo
View ArticleHP MIB
Product Name: - HP ProCurve 1800-24G J9028B- HP ProCurve 1810G - 24 GE J9450A- HP Procurve 1810-24G J9803A- HP Procurve 1810-24G J9801A- HPE FlexNetwork 5130 48G 4SFP+ 1-slot HI Switch - JH324A- HP...
View Articleexchanging FAN at HP 1820-24G POE
Does anyone know, which kind of FAN the 1820-24G POE has?Does the Switch need a PWM FAN with 4 Pins? or would a 3-Pin FAN with 12V also workThe FAN is a too loud and I'm thinking about to exchange it
View ArticleRe: HP MIB
MIBs are available at: https://h10145.www1.hpe.com/Downloads/ProductsList.aspx?lang=en&cc=us&prodSeriesId=3231819
View ArticleRe: Firmewareupgrade failed - HP ProCurve 1810G - 8 GE, P.1.6
I'm having exactly the same problems.Are there any solutions yet?
View Articlehp v1910 not marking packets
Hi, I need to prioritize two PCs, which one connects to port g1 / 0/1 and the other to port g1 / 0/2. I have an acl that includes the ip of those pc, the classifier that includes the acl, the behavior...
View ArticleHelp with V1910 Switch Configuration
Hi:We are about to test some infrastructure changes in our datacenter and my datacenter provider asked me to protect the uplink port of our core switch so we don't affect their router in case we cause...
View ArticlePort Policy Configuration Failure - HPE 1920
Hi, i'm trying to configure a port policy on several ports. I've build a classifier and a behavior, which i've then assigned to a qos policy. My problem ist, that if i try to set this policy to any...
View ArticleQOS Behavior CAS Limit - HPE 1920
Hi, i've some trouble to understand the CAR functionality in the QOS behavior setup. I can set a CIR here but under what conditions is this CIR limition done? Are packets dropped? What is the burst...
View ArticleClik here to view.
Conseil pour réalisation réseau
Bonjour,Je souhaite réaliser le réseau suivant:Le but du projet est de séparer mes caméras IP et le NAS de mon réseau local. Ma connexion Internet se fait via une livebox pro qui se charge de...
View ArticleRe: Conseil pour réalisation réseau
Pour realiser une telle separation il vous faut un routeur (ou un layer3 switch).Ni le HP1620 ni la Livebox en est capable.Il y a deux choix:1/ Au lieu de la Livebox, utiliser un routeur qui supporte...
View ArticleRe: Best method for connecting up multiple 1920 switches
In addition to what Parnassus has recommended, I would then create a 2-member LAG between A and D to complete a loop to give you redundancy should one of the switches fail, and then use STP to block...
View ArticleRe: Help with V1910 Switch Configuration
Most important: You have spanning tree enabled, so you're protected against loops. This includes the port connected to your provider.BPDU protection isn't necessary, and should be used wisely. It's...
View Article