Re: ACL VLAN HP 1920
Si c'est /17 ca va etre 10.200.0.0 0.0.127.255 ?Et vous l'appliquez sur an VLAN interface dans le resau 10.200.0.0/17?
View ArticleCondig HPE OfficeConnect1910 IP in another VLAN
Hello,I got a HPE OfficeConnect1910 switchI want to set an IP address but through the commands I was able to set it only in VLAN1 and I must it be in another VLAN.How to do this?Thank you
View Article1910 Mib OID for Buffer purposes
Hi:He have 1910/1920 series Switch comware V7 and the idea is to check if exist related with Mib Snmp(Chain and Oid,s) and regarding of this. Is this possible and How can obtain the following data (in...
View Articleشركة تخزين عفش بالرياض
عمل على تقديم خدمة تخزين الاثاث، خصوصا بالرياض، حيث ان المستودعات الرئيسيه متواجدة بالرياض، نظرا لكونها العاصمة، التي تحتكر الكثير من الاعمال، العمل على تخزين الاثاث بالرياض سهل للغاية، حيث يمكن للعميل...
View ArticleHPE 1920-24G: 4-port Trunk Link w/ 2 ports Errdisable - cabling configuration...
Good morning all,We have a HPE-1920-24G switch with a trunk link (4 Dynamic LACP ports) connected to an HP 1820. All 4 links worked previously, however due to expansion some cabling work was done (4...
View ArticleRe: HPE 1920-24G: 4-port Trunk Link w/ 2 ports Errdisable - cabling...
Is your testing testing all 8 wires?Have you tried swapping the questionable cabling into known-good ports on both sides of a known-good link to see if the problem follows the cabling?I wouldn't worry...
View ArticleRe: HPE 1920-24G: 4-port Trunk Link w/ 2 ports Errdisable - cabling...
It looks like a Layer 1 issue: what's about to verify LACP and each Port Trunk's member port status (particularly speed/duplex values) on both ends? maybe new cabling caused a speed value...
View ArticleRe: HPE 1920-24G: 4-port Trunk Link w/ 2 ports Errdisable - cabling...
I assigned speed/duplex settings on both sides but LACP negotiation still failed. To confirm I had settings set correctly I used a test switch (Netgear) to confirm LACP negotiation using new cables...
View ArticleRe: HPE 1920-24G: 4-port Trunk Link w/ 2 ports Errdisable - cabling...
After setting up an additional test switch to confirm the software/configuration side was set correctly I tend to agree with you that it's a Layer 1 issue.Will have to replace 2/4 couplers and see if...
View ArticleRe: HPE 1920-24G: 4-port Trunk Link w/ 2 ports Errdisable - cabling...
I *really* wouldn't be troubleshooting this by looking at LACP negotiation.You need to establish each link one by one and just get each port up and passing traffic before you look at any link aggregation.
View ArticleRe: HPE 1920-24G: 4-port Trunk Link w/ 2 ports Errdisable - cabling...
You wrote: "Out of curiousity, are inline couplers with punchdown blocks the norm?"IMHO No, at least when used to "extend" a data cable run...simply because, once you use them (no matter if the total...
View ArticleHow to manage Bandwidth in Switch OfficeConnect 1620
I'm trying to limit the bandwidth in its port to 2Mbps on switch officeconnect 1620. I tried it through the webbase but it did not work. Please help to tell how
View ArticleRe: HPE 1920-24G: 4-port Trunk Link w/ 2 ports Errdisable - cabling...
I've used couplers before when I had no other choice. They don't always work - like any bit of physical wiring, there is always the potential for it to not provide full connectivity.
View ArticleReplace Foundry switch with HPe 1920-48G in a STP topology
Good morning,I'm trying to replace an old Foundry switch with a new HPe 1920 switch in a stp topology enviroment. With STP enable and computer connected to it I can't reach all network's devices but...
View ArticleRe: Replace Foundry switch with HPe 1920-48G in a STP topology
Knowing nothing neither about your network topology nor about relevant devices (switches) involved, your issue probably smells about VLANs or about misconfigured (or incompatible) STP features...have...
View ArticleHP v1910-24G BAGG becomes INACTIVE because the port's configuration is...
Hello, We have 2x1910-24G switches there's a Bridge Aggregation configuration like;interface Bridge-Aggregation1port link-type hybridport hybrid vlan 251 253 507 to 508 510 to 511 520 to 531 600 667...
View ArticleHPE 1620 VLAN: how to have 1 port visible to all VLANs
I have a HPE 1620 switch connected to an Internet router and various clients. I would like to have the clients on separate VLANs, so they don't "see" each other, but all should have access to the port...
View ArticleRe: HPE 1620 VLAN: how to have 1 port visible to all VLANs
First, check to see if the 1620 supports private vlans, or port isolation. Probably not, but check.Failing that, you have two choices:1. If your switch supports routing, then each of your client VLANs...
View ArticleRe: HP v1910-24G BAGG becomes INACTIVE because the port's configuration is...
Avoid to use any Hybrid Port configuration, it's not necessary at all on the logical Port Trunk nor on its member ports.Follow this thread (it refers to setting up a 4 ports Port Trunking with LACP...
View Article