Re: How to get remote management to HPE 1920S switch?
Hi, They are in different VLANs, but that's not a problem since interVLAN routing is implemented in the network. Finally I was able to have local and remote management to the switch, but it seems the...
View ArticleRe: Constant moderate CPU usage on HPE 1950 24G 2SFP+ 2XGT PoE+ Switch
Your Switch is not doing exactly nothing...is it a PoE model, isn't?So maybe, just a guess here (due to fact that PSED acronym resembles something like PSE Deamon in my head), the PSED Task would be...
View ArticleRe: Constant moderate CPU usage on HPE 1950 24G 2SFP+ 2XGT PoE+ Switch
Amazing, why didn't I think of that. You are absolutely right, when I wrote my post I meant the switch was doing absolutely [no switching], an AP was still connected with PoE. And the name of the...
View ArticleRe: Constant moderate CPU usage on HPE 1950 24G 2SFP+ 2XGT PoE+ Switch
AFAIK the 145 is the latest PSE Firmware HPE released. Good your switch is not using an older version (143 or even older).
View ArticleRe: How to get trial license for Service Desk
> I downloaded a product called Service Desk I'm not sure how you could do that. It has been obsolete for many years and has been replaced by MF Service Manager.
View Articledot1q trunking between cisco and hp 1920
Hi,I'm having trouble trunking between our Cisco Catalyst 4500 and HP 1920G switch. Vlan 5 is not propagating, all other vlans seem to be ok. I'm not able to manage the switch, and no devices in vlan 5...
View ArticleOfficeConnect 1920S 48G Network Switch Configuration
Hi, anyone is familar to configure this model OfficeConnect 1920S 48G which was recently purchased. I was confused on how to configure the trunk, Tagging and Untagging but I have no problem to...
View ArticleRe: Ling Aggregation and LACP for HP 1920 and HP 1920s
Hi,On 1920 not S, you must change port to Hybrid and it work.You could also change automatically to Hybrid by tagging a vlan on the BAGGxOn 1920S default settings just select in TRKx "Dynamic"
View ArticleRe: OfficeConnect 1920S 48G Network Switch Configuration
Since you're used to setup Port Trunking (LAG) on HPE OfficeConnect 1910 and HPE OfficeConnect 1920 Switch series...what's about starting with the HPE OfficeConnect 1920S Switch series Management and...
View ArticleRe: dot1q trunking between cisco and hp 1920
Is Spanning Tree enabled on both uplink's ends?On Cisco Catalyst 4500 side...shouldn't be used also:switchport trunk allowed vlan 5 11 12 16 17 19to allow above VLANs through the uplink.If Spanning...
View ArticleRe: dot1q trunking between cisco and hp 1920
hi parnassus,I've made the changes you've suggested, but the issue remains.I've run'switchport trunk allowed vlan all' on the cisco switch.I'm not able to apply this command on the HP 1920port...
View ArticleRe: OfficeConnect 1920S 48G Network Switch Configuration
Hi Parnassus, thank for the advice. I will ty to figure out on the configuration. Only is the portion where shows TRK1..2...3...after Interface 50. Not sure what's that for..
View ArticleRe: How to Enable Telnet and SSH on HPE 1920s OfficeConnect
Hi, I have this issue too. I can't find a way to enable SSH. The Config Guide says "Session Type Shows the type of session, which can be Telnet, Serial, SSH, HTTP, or HTTPS." (page 33), Don't know why...
View ArticleHP1920-24G and Siemens Scalance compatibility
Hi experts,i need to connect two switches via fiber optics. One is Siemens Scalance X104-2 (multimode, 1310nm, Full duplex to 100 Base-FX) another HP 1920-24G with 4 SFP ports. Is there any compatible...
View ArticleHP JG960A 4 UPLINKS WORK TOGETER ?
Hi, I want to buy a HP JG960A but I don't know if it is possible that the 4 uplinks port ( 2 for 10 GbE Fiber and 10 GbE Copper BaseT) can use simultanesly.Thank you.
View ArticleRe: HP JG960A 4 UPLINKS WORK TOGETER ?
IMHO those two pairs (2 SFP+ and 2 XGT) can be used concurrently, they are independent each other.
View ArticleRe: HP 1920-48G Switch : Self-signed certificate ?
I too have been wanting this. I see no way to do this and have followed multiple instructins for other HP switches. I've used all other types and models of HP switches and have not had this issue...
View ArticleARP table vs Interface Statistics
Hi,I have an HP 1920 with 24 ports. There is an up stream firewall/router connected to port 24 and endpoints connected to ports 1, 17, 21 and 23. This is confirmed in the Device > Interface Stastics...
View Article