Does the HPE 1950 OfficeConnect Layer3 Support NAT?
Hello,I just purchased a HPE 1950 48-port Layer3 switch and am wondering if it support Network Address Translation (NAT)?If not, can anyone recomment a low cost solid HP router?Thanks,KM
View ArticleRe: Does the HPE 1950 OfficeConnect Layer3 Support NAT?
AFAIK the HPE OfficeConnect 1950 Switch series doesn't support NAT (it has, as Switch supporting Layer 3 lite features, only a subset of Layer 3 features and we should not forget we're speaking about...
View ArticleRe: Does the HPE 1950 OfficeConnect Layer3 Support NAT?
Thank you  parnassus :)Question, do you use the HPE FlexNetwork MSR95x or MSR93x routers? and what are your thoughts on the HPE MSR router?I am looking at using the HPE MSR95x or MSR93x router to route...
View ArticleRe: HP 1920 Switch VLAN acl/qos
You can't apply it to VLANs, you have to apply it to physical ports.Use the GUI and it will teach you what the config looks like.If all you need is a simple Layer3 switch to support multiple VLANs and...
View ArticleRe: HP 1920 Switch VLAN acl/qos
I also tried command : qos vlan-policy VLAN90p vlan 90 inboundgot same error Not supported by hardware. This means to me you Vince-Whirlwind are right and the release JG924A-CMW520-R1105 note "Modified...
View ArticleRe: HP 1920 Switch VLAN acl/qos
I didn't know they had released upgraded firmware that supposedly allowed this. Did you install the full package?
View ArticleRe: HP 1920 Switch VLAN acl/qos
"Did you install the full package?" I made the normal firmware upgrade to 1920-24G-JG924A_5.20.R1119
View Article503 Service Unavailable
Hi I have a stack of two HP 2920 switches. I can no longer access the web interface and get the following error. 503 Service UnavailableThe server is currently busy. Please try again laterWorked fine...
View ArticleHPE 1950 Switch JH295A does not increment SNMPv3 engine-boots when it is...
Hi,Usually SNMPv3 engine-boots should increment if device is rebooted. For HPE 1950 switcheswith latest firmware engine-boots are not incremented and are always set to 1. ThereforeSNMPv3 does not work...
View ArticleHPE 1920S will not allow communication between a Ruckus ZoneDirector and the...
I administer a network at a school where we have a Ruckus ZoneDirector 1112 controlling 13 Ruckus ZoneFlex Access Points of varying types. A while ago the Netgear ProSafe GS724TP PoE switch failed so I...
View ArticleRe: HPE 1920S will not allow communication between a Ruckus ZoneDirector and...
Check on 1920S if its configuration has enabled all/some Advanced Security parameters (Security -> Advanced Security): if so try to disable them all (Auto DoS Features and ICMP Settings).Clearly...
View ArticleRe: HPE 1920S will not allow communication between a Ruckus ZoneDirector and...
As mentioned, I believe this problem is related to Vlan or security features (I believe it to be vlan ) !If the Controller and AP's communicate in the same L2 domain, that should be the problem. In an...
View ArticleRe: HPE 1920S will not allow communication between a Ruckus ZoneDirector and...
Thank you for the responses. I will try disabling all of the security features today to see if that helps.No VLANs have been configured at this site so all ports and devices and simply using the...
View ArticleRe: HPE 1920S will not allow communication between a Ruckus ZoneDirector and...
- When you had this problem were you able to access the ZoneDirector and ZoneFlex Access point consoles? I have no problem accessing either the ZD or ZF via their web consoles regardless of where they...
View ArticleRe: HPE 1920S will not allow communication between a Ruckus ZoneDirector and...
Thank you for the help guys.The solution turned out to be one of the Auto DoS features on the switch as suggested by .The offending feature was 'Prevent UDP Blat Attack'. As soon as I disabled this the...
View ArticleRe: What cause a port to go in to Administrative Mode D-Disabled
Hello !Post the configuration file for your switch and syslog for when the problem happens. Both you can collect through the web interface.
View ArticleRe: Config link aggregation between ESXi 6.0 U3 (free edition) and Switch HP...
Hello!Yes. ESXi only supports LACP on Distributed Switches. You need a non-protocol link aggregation.More information in KB...
View ArticleRe: Question About best configuration
Hello !What is your problem or difficulty with this configuration? Do you have a physical and logical topology design?
View ArticleLACP in Procurve 1800 family switch
Hello,I'm wondering if the LACP protocol in Procurve 1800's family switches is based only on MAC address or uses also IP informations. I need to configure link aggregation of two Qnap NAS and I'm not...
View Article