Quantcast
Channel: All Web and Unmanaged posts
Viewing all 3315 articles
Browse latest View live

Configure HP-1950 48port JG963A with trunking

$
0
0

Hi,

 

I need some help to setup a high availability wireless connection b/w two sites with two radio wireless devices. For the moment i have issues with the existing wireless connection as it drops off packets anytime during the day and on some occasions i have to restart it to bring it back online.

I have a HP-1950 JG963A switch with default VLAN ID 1 and untagged ports. On each site i have two radio wireless devices to connect the two sites, for the moment one pair of wireless device is disconnected to avoid creating network loop.

I like to know how to setup the HP switch ports of both wireless devices on both sites to use two pairs of wireless devices as high availability connection amongst sites. I am confused if i have weather i have to setup trunk ports on both switches with or without port aggregation.

 

Best Regards,

Syed

 


V1910 ACLs

$
0
0

Hello, 

I have been working on trying to configure ACLs on a V1910 for over 2 weeks now and I'm beyond frustrated. I have updated to the latest firmware. I have read countless articles and done many searches. I have tried to configure them via the CLI as well as through the GUI with no success. I have several VLANs on the switch and they can all route between eachother. I am trying to restrict traffic on VLAN 28 10.10.28.0/24 from getting to any other VLAN and also restrict all traffic on VLAN 22 10.10.22.0/24 from getting to any other VLAN but allowing port 25 from VLAN 22 to VLAN 24 10.10.24.0/24 and also allowing VLAN 22 to get to the internet (VLAN 10 has the gateway/edge firewall on it). I also want to allow VLAN 24 to be able to get to every other VLAN, including 22 and 28.

 

Any help would be amazing. 

Thanks,

Jason

Loopback Detection

$
0
0
Hi!
The HPE 1910 JG538A and 1908 + POE Loopback Detection switches do not work. If I disable RSTP Global and enable Loopback Detection on the system + enable ethernet all. If you turn for example patchcord eth1 / 02 in 1/0/6, the switch hangs loopback Detection does not work.
I'm using software 5.20.R1118.
Should Loopback Detection work? Do you work at the test?

Problems with POE after upgrade - Power PSU1 failed - V1910-24G-PoE (365W) JE007A

$
0
0

Hi,

The HP V1910-24G-PoE (365W) switch, model JE007A, after I tried to upgrade to version 1910_5.20.R1513P99, the POE stopped working, I tried to go back to the old version, but the POE did not work again.
Could you help me solve this problem?

LOG:

Apr 24 15:54:37:517 2018 IFNET Error LINK_UPDOWN GigabitEthernet1/0/4 link status is DOWN.
Apr 24 15:54:37:516 2018 IFNET Error LINK_UPDOWN GigabitEthernet1/0/2 link status is DOWN.
Apr 24 15:54:36:719 2018 MSTP Information MSTP_FORWARDING Instance 0's port GigabitEthernet1/0/4 has been set to forwarding state.
Apr 24 15:54:36:703 2018 IFNET Error LINK_UPDOWN GigabitEthernet1/0/4 link status is UP.
Apr 24 15:54:34:914 2018 MSTP Information MSTP_FORWARDING Instance 0's port GigabitEthernet1/0/2 has been set to forwarding state.
Apr 24 15:54:34:898 2018 IFNET Error LINK_UPDOWN GigabitEthernet1/0/2 link status is UP.
Apr 24 15:54:29:794 2018 DEVM Notification POWER_RECOVERED Power PSU1 recovered.
Apr 24 15:47:14:596 2018 DEVM Critical POWER_FAILED Power PSU1 failed.
Apr 24 15:47:09:793 2018 DEVM Notification POWER_RECOVERED Power PSU1 recovered.
Apr 24 15:46:28:993 2018 DEVM Critical POWER_FAILED Power PSU1 failed.
Apr 24 15:46:23:393 2018 DEVM Notification POWER_RECOVERED Power PSU1 recovered.
Apr 24 15:46:00:993 2018 DEVM Critical POWER_FAILED Power PSU1 failed.
Apr 24 15:42:15:378 2018 IFNET Error LINK_UPDOWN GigabitEthernet1/0/3 link status is DOWN.
Apr 24 15:42:14:639 2018 IFNET Error LINK_UPDOWN GigabitEthernet1/0/4 link status is DOWN.
Apr 24 15:42:14:480 2018 IFNET Error LINK_UPDOWN GigabitEthernet1/0/2 link status is DOWN.
Apr 24 15:42:14:480 2018 IFNET Error LINK_UPDOWN GigabitEthernet1/0/1 link status is DOWN.
Apr 24 15:42:10:590 2018 MSTP Information MSTP_FORWARDING Instance 0's port GigabitEthernet1/0/3 has been set to forwarding state.
Apr 24 15:42:10:568 2018 IFNET Error LINK_UPDOWN GigabitEthernet1/0/3 link status is UP.
Apr 24 15:42:08:306 2018 IFNET Error LINK_UPDOWN GigabitEthernet1/0/3 link status is DOWN.
Apr 24 15:42:01:807 2018 MSTP Information MSTP_FORWARDING Instance 0's port GigabitEthernet1/0/4 has been set to forwarding state.
Apr 24 15:42:01:784 2018 IFNET Error LINK_UPDOWN GigabitEthernet1/0/4 link status is UP.
Apr 24 15:42:01:783 2018 MSTP Information MSTP_FORWARDING Instance 0's port GigabitEthernet1/0/2 has been set to forwarding state.
Apr 24 15:42:01:758 2018 IFNET Error LINK_UPDOWN GigabitEthernet1/0/2 link status is UP.
Apr 24 15:42:01:569 2018 MSTP Information MSTP_FORWARDING Instance 0's port GigabitEthernet1/0/1 has been set to forwarding state.

Thanks in advance

Create a DHCP server on a HP Office 1920 switch

$
0
0

Hi there,

 

Just wondering is it possible to create a DHCP server on a Office 1920 switch??  I want to create a guest wifi off my network and use this switch as a DHCP server to give out IP addresses for people who connect to the guest WIFI service.

Thanks

Paul

Re: Create a DHCP server on a HP Office 1920 switch

$
0
0
I'm afraid that HPE OfficeConnect 1920 Switch series doesn't provide any DHCP Server feature; DHCP Client, DHCP Relay and DHCP Snooping are supported features.

Problem hard reset switch HP V1910-24G Switch

$
0
0

follows the error print. how to solve?

Screenshot from 2018-04-27 19-13-04.png

Re: Loopback Detection

$
0
0

Are you confusing "Loopback test" with Loop guard?

MSTP includes Loop Guard, if you have it enabled. RSTP probably doesn't. As far as I know there is no specific configuration for enabling Loop guard, just enabling MSTP enables it.

Also, patching two switchports on the same switch into each other is not what Loop guard is designed to prevent. STP takes care of loops on the switch, Loop guard takes care of remote loops.

 

 


Re: Hp 1920 Vlan Setup

$
0
0

Hi, I had the same setup, I've set my tplink dhcp server with my vlan IP where it's connect on, renew address on each PC outside the 1920s and everyone can ping each other.

HP 1950 stacking via Ethernet, can I use SFP+ for trunks?

$
0
0

Hi all

Looking at 7 x 1950 48G PoE+ 10Gbe/10G SFP+ switches for a network upgrade.

Planning to stack 4 units via 10G copper ports and have the other 3 stanadlone on other floors in wiring closets.

If stacking 4 switches via 10G copper, this leaves me with 8 SFP+ ports, can I use these ports as trunk ports to ESXI servers and the other 3 standalone switches?  No dual personality/combo issues?

I did check the manual and Google and found nothing leading me to believe they are dual personality/combo ports but I thought I'd get confirmation first before pulling the trigger on these devices.

 

Many thanks.

Re: HP 1950 stacking via Ethernet, can I use SFP+ for trunks?

$
0
0

: don't worry, the two SFP+ slots (for SFP or SFP+ Transceivers) and two 10G Base-T ports aren't combo (no combo options on the entire HPE OfficeConnect 1950 Switch series: JH295A, JG960A, JG961A, JG962A and JG963A).

Also no particular restrictions are valid with regard to logical IRF ports (stacking logical ports) binding to physical interfaces: that means that you can eventually mix one SFP+ interface and one 10G BASE-T interface by binding them to the same logical IRF Port without worrying that you should use all or nothing (all 10G BASE-T or all SFP+). Also no 10G ports grouping seems to be present (so you're free to use, let me say, one 10G BASE-T or one SFP+ port for IRF and the remaning others for LAGs - Link Aggregation Group(s) - or just single link uplinks to other Switches).

Screenshot_2018-05-04_16-30-51.png

Screenshot above taken from HPE OfficeConnect 1950 Switch Series Getting Started Guide.

 

 

 

Re: HP 1950 stacking via Ethernet, can I use SFP+ for trunks?

$
0
0

Thanks for the speedy and accurate response!

@EV@>> tulsacampfire.org/123movies-2018-watch-avengers-infinity-war-online-movie-hd-full-free

Config link aggregation between ESXi 6.0 U3 (free edition) and Switch HP 1920-48G JG927A

$
0
0

I'm trying a couple of days to set up a link aggregation between an HP Switch HP 1920-48G JG927A and ESXi 6.0 U3 (free version). J; I've tried several configurations and algorithms of LACP (in ESXi), but the maximum I could do was to create a failover with 4 links ... one of them is active and the others in failover mode. But what I want is to join 4 1GB link to create a 4GB link.

I also read that this would only be possible in the paid version of ESXi, since it would have to use a distributed switch and not the virtual switch that the free version provides. That's right?

Live long and prosper,
Marcelo Magalhães
Rio de Janeiro - Brasil

Re: HP 1920-8G firmware, where to download?

$
0
0

I don't understand this.

HP is such a big company, but the support is so bad. It's very difficult these days to find even a simple firmware update!


HP 1920 Switch VLAN acl/qos

$
0
0

Like many others HP 1920-24G Switch (JG924A) owners I have problems trying to isolate traffic between VLANs.
Firmware is JG924A-CMW520-R1119 and release notes stated:

Starting JG924A-CMW520-R1105
Modified features include: An ACL can be applied to multiple ports or VLANs

In cli command "interface Vlan-interface90" dont allow "packet-filter" command but only "qos".
Anyway applying command "qos apply policy VLAN90p inbound" returns:
Error: Setting qos policy failed.
Reason: Not supported by hardware.

I have two VLAN:
VLAN1 10.0.2.0/24 production where is the firewall for Internet 10.0.2.254
VLAN90 172.16.90.0/24 wifi guest DHCP relay to DHCP server 10.0.2.12 with scope 172.16.90.0/24 and releasing option gateway/router 10.0.2.254 DNS server 10.0.2.254
Obviously I want client wifi guest only access to Internet through 10.0.2.254, deny access to any other networks.
All Vlans are already created, each vlan with an IP so I can route between VLAN's each other and to Internet.
Here's the part of my config:
#
 version 5.20.99, Release 1119
#
 sysname HP-1920G-Switch2
#
 dhcp relay server-group 1 ip 10.0.2.12
#
interface Vlan-interface1
 ip address 10.0.2.52 255.255.255.0
#
interface Vlan-interface90
 ip address 172.16.90.1 255.255.255.0
 dhcp select relay
 dhcp relay server-select 1
#
 ip route-static 0.0.0.0 0.0.0.0 10.0.2.254
#
interface GigabitEthernet1/0/22
 port link-type trunk
 port trunk permit vlan 1 90
 port auto-power-down
 stp edged-port enable

In port 22 I connected one access point TP-Link EAP225 (VLAN aware) with two SSID:
SSID        VLAN
VLAN80        0 (means default VLAN 1)
VLAN90        90
thus link-type trunk needed to carry diffferent VLAN ID. VLAN80 is only SSID name but is on VLAN id 1.

All works like a charm and when a wifi client connect to network SSID VLAN90 got IP from DHCP ip 172.16.90.x this means to me VLAN config and related DHCP relay work fine. The client reach both VLAN1 devices and Internet. Now I want to isolate the VLAN 90 and I made these configuration on switch:

#
acl number 3500
 description guest wifi VLAN90
 rule 3 permit udp destination-port range bootps bootpc
#
traffic classifier VLAN90 operator and
 if-match acl 3500
#
traffic behavior VLAN90b
 filter permit
#
qos policy VLAN90p
 classifier VLAN90 behavior VLAN90b

the acl configuration now is not correct but it is not important because any kind of deny/permit in ACL I set anyway I got:

[HP-1920G-Switch2-Vlan-interface90]qos apply policy VLAN90p inbound
Error: Setting qos policy failed.
Reason: Not supported by hardware.

The correct ACL I suppose will be :
acl number 3500
 description guest wifi VLAN90
 rule 3 permit udp destination-port range bootps bootpc
 rule 5 permit ip source 172.16.90.0 0.0.0.255 destination 10.0.2.254 0.0.0.0
 rule 50 deny ip

Why the error "Not supported by hardware"

Thanks

Re: HP 1920 Switch VLAN acl/qos

$
0
0

Why not using (are you?) the Web GUI's QoS menu [*] to setup a basic/advanced IPv4 ACL instead of Switch CLI?

That way grayed-out options cannot be configured (I suppose both through Web GUI and through CLI) and so you will recognize that immediately.

[*] QoS sub-menu: Summary, Add, Basic Setup, Advanced Setup, Link Layer Setup and Remove.

Re: HP 1920 Switch VLAN acl/qos

$
0
0

Hy parnassus,

The problem is not configuring qos but apply qos to VLAN interface that give the above error.

Web GUI's QoS menu (I know well) finally wrote cli command into configuration file so using web or cli take you to the same point.

I dont think there is a Web GUI menu for qos apply to a Vlan interface in this switch but only advanced cli. But cli gave that error and we dont know why.

 

 

HPE 1920S (JL380A) firmware update fails

$
0
0

Hello community,

I'm trying to update my HPE 1920S (JL380A) switch from firmware version PD.01.07 to firmware version PD.01.08, but that fails. I'm using HTTP method under "Maintenance - Backup and Update Manager". The error message is:

"Transfer Failed. An unexpected error occured. Please try again". See also attached screenshot.

I reeboted the switch, tried other browsers and downloaded the firmware file PD.01.08.stk several times but everything failed.

Anyone here having the same issue?

Many thanks in advance for your support!

What cause a port to go in to Administrative Mode D-Disabled

$
0
0

J9983A HPE OfficeConnect 1820 24G PoE+ (185W) Switch

Firmware: PT.02.03 (Build date:30-Jun-2017)

I have one port that from time to time goes in in Admin Mode D-Disabled: Automatically disabled by the system due to error conditions. For example, an interface may be disabled if it exceeded its rate limit.

Please someone can help troubleshhot this kind of problem?

 

Viewing all 3315 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>